Frigid-X Cabinet Panel Coolers And Electronic Control Panel Coolers

Process Controls Index
Process Controls Index

Air Jets And Nozzles
Air Jets And Nozzles
Air Jets
Air Nozzles

Web Site
www.nex-flow.com

Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers

How It Works:

Compressed air enters at point (A) into the vortex tube component of the panel cooler. The vortex tube splits the compressed air into a hot (B) and cold (C) stream of air. The hot air from the vortex tube is vented to the atmosphere at point (D) after being muffled to reduce noise. Hot air displaced from inside the control panel or cabinet is exhausted through point (E). Cold air enters into the panel (F) via the cold distribution hose (G). Holes (H) are punched into the hose kit to deliver the cold air inside the panel where required. A muffler (I) further reduces the noise level of the exhausting air.

Why Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers

Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers are made from all metal parts, stainless steel body, quiet - tests show Frigid-X™ Electronic Control Panel Coolers to be constantly quieter than the competition! Our standard units are good in ambient temperatures up to 150ºF (67ºC). High temperature unitsareavailable to 200ºF (93ºC) and higher. Non hazardous purge units are also available where constant flow is required to purge a control panel but maintain On/Off operation to conserve energy.

Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers Selection

Frigid-X,Cabinet Panel Coolers,Electronic Control Panel Coolers,Cabinet,Panel,Coolers,Electronic,Control Panel,NEMA Type 12,IP52,NEMA Type 3R,IP14,NEMA Type 4-4X,IP56,NEMA,12,IP52,3R,IP14,4-4X,IP56 Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers are available with thermostat control (On/Off units) or continuous operation. Continuous systems are best when constant cooling and/or a positive purge of the panel is required. On/Off control saves air by activating the unit when the internal temperature a critical level. the adjustable thermostat is factory set at 95ºF (35ºC). They are best used in applications where heat may fluctuate as in variable speed drives and where continuous purge is not required. All of our Frigid-X™ Cabinet Panel Coolers and Cabinet Enclosure Coolers are stainless steel for long life and flexible environments.

If a constant positive pressure is required with On/Off control (non-hazardour purge units) a special solenoid valve can be supplied to allow a small amount of air flow into the control panel when in the closed position. High temperature units for ambient temperatures in excess of 150ºF (67ºC) to 200ºF (93ºC) and higher are available.

Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers Versus Other Options

Heat pipes and air to air heat exchangers cannot cool below ambient temperature limiting the cooling effect. Filters require monitoring and change to prevent failure.
Water cooled heat exchangers use water which is not compatible to electronics. In addition scale build-up can cause reduced effectiveness over time downtime for descaling.
Refrigerent CFC or HCFC heat exchangers are more costly with higher installation costs aand lower life expectancy. Installation requires a floor drain for condensate. Machine vibration can cause loss of refrigerant and component failure. Replacement cost of a compressor can be high. Filters require monitoring and change to prevent failure.
Frigid-X™ Cabinet Panel Coolers And Electronic Control Panel Coolers are low cost with NEMA Type 12 (IP52), NEMA Type 3R (IP14) and NEMA Type 4-4X (IP56) models available. They are compact, easy and fast to install. Thermostatic control minimizes air use to only when needed. They are approved by Underwriters Laboratory (ULC Component Recognized) to meet USA and Canadian standards, and meet CE regulations and necessay international standards.
<< NEXT>> | << BACK >>